Epoxy self-leveling floor paint is prepared with 100% solid content of special epoxy resin as the base material. It has the excellent characteristics of green environmental protection, high gloss, one-time film thickness, paint film toughness and wear resistance. It is an ideal floor painting system for electronic enterprises, pharmaceutical enterprises, large parking lots and other places requiring high cleanliness. So what is the thickness of epoxy self-leveling floor paint? Generally speaking, the standard process thickness of epoxy self-leveling floor paint is about 1.5mm. The specific process is as follows:
1. Floor milling processing: Milling the ground with a high-speed multi-head professional ground milling machine, removing the concrete slurry on the ground surface 1-2 mm and leveling the ground. In this process, 16 milling planers are used to increase the roughness of the concrete base and the leveling of the ground. The ground is treated with a special shot blasting machine. Add grass-roots wool.2、环氧底涂：将环氧底涂材料安装说明书配比配制并搅拌均匀，然后用滚筒均匀地滚筒于地坪表面，此工艺可以重复施工，直至完全封闭混凝土毛细孔，伸缩缝、施工缝采用贴布处理。(材料用量0.2kg/㎡，结膜厚度0mm)。
2. Epoxy primer: mix and mix the epoxy primer material in the installation instructions evenly, then use the drum to evenly roll on the surface of the floor. This process can be repeated construction until the concrete capillary holes are completely closed, and the expansion joints and construction joints are treated by sticking cloth. (Material dosage was 0.2 kg/, conjunctival thickness was 0 mm).3、砂浆中涂：在配置好的环氧中涂材料中加入一定比例的石英砂并搅拌均匀，然后用镘刀将配置好的砂浆中涂材料均匀地镘涂于完全固化后的底涂表面，待其完全固化后打磨吸尘。(材料用量0.4kg/㎡，结膜厚度0.5mm)。
3. Intermediate coating of mortar: A certain proportion of quartz sand is added into the prepared epoxy coating material and stirred evenly. Then, the coated material of the prepared mortar is uniformly coated on the fully cured surface of the undercoat with a trowel knife, and the dust is polished and cleaned after it is completely cured. (Material dosage was 0.4 kg/, conjunctival thickness was 0.5 mm).4、批涂：在配置好的环氧中涂材料中加入一定比例的碳酸钙粉并搅拌均匀，然后用镘刀将配置好的中涂材料均匀地批涂于完全固化后的底涂表面，此工艺施工后要达到手感光滑，避免沙眼、马蜂窝现象。(材料用量0.2kg/㎡，结膜厚度0.15mm)。
4. Batch coating: add a certain proportion of calcium carbonate powder into the prepared epoxy coating material and mix evenly. Then use a trowel knife to evenly batch the prepared coating material onto the fully cured surface of the base coating. After the construction of this process, the handle should be smooth and the trachoma and honeycomb phenomena should be avoided. (Material dosage was 0.2 kg/, conjunctival thickness was 0.15 mm).5、环氧面涂：首先将彩色面涂自流平材料按一定比例精确配置并搅拌均匀，然后用镘刀将配置好的彩色面涂材料均匀地镘涂于上工艺表面，达到颜色均匀一致，有晶面效果。(材料用量1kg/㎡，结膜厚度0.85mm)。
5. Epoxy surface coating: First, the self-leveling material of the color surface is accurately collocated and stirred evenly in a certain proportion. Then, the collocated color surface coating material is evenly coated on the upper process surface with a trowel knife to achieve uniform color and crystal surface effect. (Material dosage was 1 kg/, conjunctival thickness was 0.85 mm).当然，环氧自流平地坪漆的厚度可以根据甲方要求做成2mm、3mm等厚度，只需要在施工时增加环氧砂浆层的厚度即可。
Of course, the thickness of epoxy self-leveling floor paint can be made into 2mm, 3mm and other thickness according to Party A's requirements, only need to increase the thickness of epoxy mortar layer during construction.
标签:   环氧地坪 地坪 环氧地坪漆 环氧地坪施工 北京环氧地坪